Call Now for a Free EstimateSame-Day Service(619) 808-6343

San Diego Gate Repair

Door & Roll repairs gates, under a California contractor license whose class covers gate work, and you can call us 24/7.

How Your Gate Hangs Decides What Wears

A swing gate hangs from hinges on a post. A sliding gate rolls on wheels along a ground track. A cantilever gate hangs from roller carriages on its posts and never touches the drive at all. Find your kind of gate in the rows below.

Gate, and what you noticeWhere the trouble usually is
Swing: the free end has dropped and scrapes the driveA swing leaf puts its whole weight on its hinges and the post they hang from. Worn hinge pins, a post that has begun to lean in its footing, or a frame that has racked out of square all let the free end sink. The operator then drags the leaf on every cycle and wears along with it.
Swing pair: the leaves meet out of turn or clashOn many double gates one leaf overlaps the other, so the operator holds one back for a moment when closing. If that delay is set wrong, or one leaf has slowed because of a stiff hinge or a worn arm, the two arrive in the wrong order and knock or stall.
Swing: the leaf slams its stop, or quits short of itA swing gate should come to rest against fixed gate stops when fully open and fully shut. A stop that has bent or worked loose, or limit settings that have drifted, lets the leaf overrun or halt early, and both strain the arm and its brackets.
Swing: the arm knocks or shudders mid-swingThe arm is bolted to the post at one end and to the gate at the other. A loose bracket at either end, or a worn pivot pin, lets the arm rock before it pushes, so the leaf lurches instead of swinging smoothly.
Sliding: it rides up, wanders or leaves the trackMany ground-track gates roll on V-groove wheels sitting on an angle-iron rail. Wheels worn flat, a rail that has bent, sunk or filled with grit, or top guide rollers that no longer hold the panel upright, let the gate climb off its line.
Sliding: it stalls at the same spot on every runA stall that always happens in one place points to something fixed along the run: a kink or high spot in the rail, a length of gear rack that has worked loose or lost teeth, or rack that has drifted out of line with the drive gear.
Cantilever: the nose droops or the panel bindsWith no wheels on the ground, a cantilever panel depends on the rollers inside its carriages and on the bolts holding those carriages to the posts. When either wears or loosens, the leading end drops and drags, or the panel binds as it passes through.
Any automatic gate: it won't shut, with no car near itMany automatic gates have wire loops cut into the drive. An exit loop opens the gate for cars leaving, and safety loops on either side of the gate's path hold it while a car sits over them. A loop that has cracked along with the concrete, or a detector that needs resetting, can hold the gate open with nothing there. A photo eye that has been bumped out of aim does the same.
Any automatic gate: the motor runs, the gate doesn'tThe drive has come apart from the gate somewhere between motor and panel: a swing arm unpinned from its bracket, a chain off its sprocket, a drive gear no longer meshing with the rack, or a manual release that was used and never set back.
Any automatic gate: it opens when nobody askedThe exit loop is a common cause: something metal left over it, damage to the loop wire, or a detector set too sensitive. A sticking keypad or remote button, or a fault in the control board, can do it too.

Before You Touch a Stuck Gate

  • Never push or pull on a powered gate to help it along. An auto-close timer or somebody's remote can start it while your hands are on it.
  • If you must move it by hand, switch the power off first and use the manual release exactly the way the operator's manual describes.
  • Keep fingers away from wheels, hinges and the gap where the gate passes its post.
  • If a car or a person is stuck on the wrong side, say so at the start of the call.

Gate, Opener or Sensor?

An automatic gate is three systems working as one: the gate, the gate opener that moves it (installers call it the operator), and the safety and entry devices around them. Trouble in one of them often looks like trouble in another.

The Gate Itself

On a swing gate that means the hinges, the posts they hang from, and the latch or lock. On a sliding gate it is the wheels, the ground track, the guide rollers that keep it upright, and the stops at each end of its run. A cantilever gate adds the roller carriages it hangs from.

Likely the gate: it drags on the drive, sits crooked or misses its latch, and it still feels stiff when moved by hand with the opener released.

The Gate Opener (Operator)

The motor and gearbox, the control board, and the limit and force settings that decide where the gate stops and how hard it pushes. Add the arm, chain or gear rack that does the moving, the manual release, and a backup battery where one is fitted.

Likely the opener: once released, the gate moves freely by hand, yet under power it hums, stops short or does nothing at all.

Sensors and Entry Controls

Photo eyes across the opening, safety edges on the gate, and vehicle loops cut into the driveway. Then the controls people use: keypads, remotes, intercoms or call boxes, and card readers.

Likely a sensor or control: the gate reverses or stays open with nothing in its path, or only one way of opening it has stopped working.

Is it the opener on your garage door, not the gate? That has its own page: garage door opener repair.

Gates Are Written Into Our License

Can a garage door company do gates? In California the answer sits in the license. Every contractor license carries a classification, and ours names gates outright.

Door & Roll's license number is #1081591. It is issued under classification C-61/D28, and the official name of that class is Doors, Gates and Activating Devices.

The Contractors State License Board's write-up of D-28 covers installing, modifying and repairing doors for homes, businesses and industry. It also names gates, power-activated doors, and card-activated equipment and other access-control devices.

A class marks out what the state permits. It is not a promise that one company does every job inside it, so tell us about your gate when you call.

You can check us yourself: search 1081591 on the CSLB license lookup to see its status and classification.

Beyond the license, Door & Roll carries insurance and is a BBB Accredited Business rated A+. Its Google rating is 4.9 stars over 600+ reviews. The About page has the rest of the story.

A Safe Gate Stops for People

An automatic gate is a heavy machine that moves on its own. Here is what keeps it from hurting anyone, written for owners rather than installers.

What Should Stop It

  • Photo eyes across the opening, so a broken beam halts or reverses the gate.
  • Sensing edges along the gate's leading edge, which react when they are touched.
  • The operator's own obstruction sensing, which stops it when it meets resistance.

Gate operators built to the current UL 325 standard monitor their external safety sensors and won't run normally when one is missing or faulty. A gate that suddenly refuses to close can be that system doing its job.

Where People Get Hurt

  • Between a sliding gate and the post or fence it slides past.
  • At exposed wheels and rollers.
  • In the gap on the hinge side of a swing gate.
  • Through open pickets or wide gaps, where a hand can reach moving parts.

House Rules Worth Keeping

  • The vehicle gate is for vehicles. People on foot should use a separate walk-through gate.
  • Warning signs belong on each side of the gate.
  • Remotes and keypads are not something for children to play with.
  • Fixed controls belong where the person pressing them can see the gate but can't reach it.
  • Everyone who uses the gate should know how its manual release works.
  • Test the photo eyes and edges as often as the operator's maker says to.

Standards to Ask About

UL 325 is the safety standard for gate operators. ASTM F2200 covers the gate itself, including covered rollers, gate stops, and screening over openings near moving parts. When anyone quotes you a new operator, ask how the installation meets both.

Gather These Before You Phone

Gate calls go better when the person on the line can picture the gate, and most of this is easy to collect.

  • The label on the opener

    Make and model are printed on a sticker or plate on the opener housing. Snap a picture of it so you can read it out or send it.

  • A short video

    Film the gate trying to move. A straining motor or a grinding wheel sounds different from a gate that simply won't start.

  • Which way it's stuck

    Say whether it is jammed open or jammed shut, and whether a car or a person is trapped on either side.

  • Getting to the gate

    The gate code, who can meet the visit, and whether a dog will be out in the yard.

  • When it started

    Mention when the trouble began and anything that came just before it: a power cut, a storm, a bump from a car, or work done near the gate.

  • Where the power comes from

    If you know which breaker or outlet feeds the opener, mention it. On a gate with no power, the supply is the first thing to rule out.

What a gate repair costs depends on what the gate turns out to need. A loose hinge or a worn wheel is lighter work than a failed control board. A big, heavy leaf takes more handling than a small, light one. Rust can turn one seized part into several, and a gate on a slope or in a tight side yard is slower to work on. Whether the photo eyes and edges are present and working matters as well.

Answers for Gate Owners

The gate won't close, or a car is shut in behind it: what now?

A gate that won't close leaves the property unsecured, so keep an eye on it rather than trying to drag it shut. A car shut in behind a closed gate is where the manual release earns its keep: switch the opener off first, then release it the way its manual says. If you have never worked a release before, leave it alone rather than guess.

Phones are answered 24/7 on (619) 808-6343.

How do I open the gate by hand in a power cut?

Turn the opener off at its breaker or disconnect first, so it can't lurch back to life when the power returns. On a swing gate the release is often on the arm or the opener box, worked with a key or a lever; once it is free, the leaf can be walked open. On a sliding gate the release separates the drive from the chain or rack, and the panel then rolls along its track by hand.

Releases differ from one opener to the next, so keep the manual where you can find it in the dark.

Why does the gate back up when nothing seems to be there?

Something told it to. Low sun shining straight into a photo eye, a safety edge with a damaged cable, or a loop reading a car that has already gone can all make a gate stop and reverse. So can the opener's own force sensing, if a stiff hinge or a dragging wheel now makes the gate harder to push than it was when the settings were made.

One remote quit but the keypad still works. Is the opener failing?

Probably not. When other remotes still open the gate, the fault is most likely in that one remote: try a fresh battery first, then check whether it has lost its pairing with the opener's receiver. Pairing steps differ from brand to brand and are in the operator's manual. If every remote stopped at the same moment, the receiver or its antenna is the more likely suspect. A keypad wired to the opener doesn't go through the receiver, so it can keep working after the receiver has failed.

One Call for Gate Repair

(619) 808-6343 is answered at any hour. You can also send the details through the quote form.

(619) 808-6343